-
Material = 303 Stainless Steel These shaft couplers require a 3/32 hex key. Bore: 1/4" to 8mm|Length: .75"|Diameter: .50"
-
Material = 303 Stainless Steel These shaft couplers require a 3/32 hex key. Bore: 1/8" to 4mm|Length: .75"|Diameter: .42"
-
Material = 303 Stainless Steel These shaft couplers require a 3/32 hex key
-
These hubs use a 7/64" Hex Key These hubs utilize a 0.770" hub pattern.
-
This clamp requires a 7/64" Hex Key To make these hubs compatible with our 0.770" hub pattern, use our 1.50" x 0.770" Hub Adaptor.
-
Material = 303 Stainless Steel These shaft couplers require a 3/32 hex key
-
Uses a 3F Standard Spline (25T) Width = 1/4" (.250") /Pressure Angle = 20° FTC Legal
-
Uses a 3F Standard Spline (25T) Width = 1/4" (.250") /Pressure Angle = 20° FTC Legal
-
Uses a 3F Standard Spline (25T) Width = 1/4" (.250") /Pressure Angle = 20° FTC Legal
-
The 10-32 set screw requires a 3/32" Hex Key (sold separately) Compatible with our 1/4" PrecisionShafts and 1/4" D-shafts. Manufactured from hardened brass
-
Material: Aluminum Coupling Style: Clamping Hole Pattern: 0.770"
-
(1) Servo Plate (1) Ball Bearing Plate (1) Servo Spline Shaft Hub (2) Hub Plates (12) 6-32 Screws Weight (no servo): 1.3 oz Perfect for robotics, animation, pan & tilt, and just about any project requiring servo power!
-
Weight: 1.632 oz (no servo) Compatible with standard size Hitec or Futaba servos (sold separately). Utilizes both the .770" and 1.50" hub pattern.
-
Material = 303 Stainless Steel These shaft couplers require a 3/32 hex key. Bore: 1/8" to 6mm|Length: .75"|Diameter: .42"
-
Uses C1 Standard Spline Width = 1/4" (.250") / Pressure Angle = 20° FTC Legal
-
The 10-32 set screw requires a 3/32" Hex Key (sold separately) This coupler is made specifically for the Futaba 25 tooth spline. Compatible with our 1/4" Precision Shafts and 1/4" D-shafts.
-
Product Weight: 1.3 oz (no servo) Servo Spline Compatibility: 24T spline Servo Size Compatibility: Standard Size Servo
-
Product Weight: 1.3 oz (no servo) Servo Spline Compatibility: 25T spline Servo Size Compatibility: Standard Size Servo
-
20° Pressure Angle O.D. = Outside Diameter P.D. = Pitch Diameter A = Bore (Nominal shaft hole A is for a tight press fit on given shaft size) A- 1/4" P.D.- 1.375" O.D.- 1.438" B- .437" C- 1.168" G- .437" E = 0.095" F = 0.185"
-
1/2" OD x 1/4" ID bearings Weight: 0.65 oz (each) Use with aluminum, carbon fiber, or steel tubing. Works great with PVC too! For mounting inside, we suggest using a 6-32 tapped standoff and 1/4" plastic spacers (shown above).
-
Simply slide on a shaft and tighten the set screws. These adaptors work with any wheels that accept a 12mm hex pattern. These adaptors require a 3/32 hex key.